This flexible, non-cracking modeling paste can be used to create a hard surface, as a filler or primer on foam. Also use as a road base or sealer under water features, or use with Soft Flake Snow™ to model heavy snow drifts. 16 fl oz.

Hot foam wire cutter for constructing a layout.

Adds versitility and functionality to the Hot Wire Foam Cutter. Adjusts for precise angles and consistent cuts 1/4" to 5".

Package includes 2 Profile Boards and 2 Connectors. Use the interlocking Profile Board pieces to create the layout perimeters and mountain profiles. Place Boards end-to-end or stack to any height using the Connectors. Trim Profile Boards with the Hot Wire Foam Cutter or a Foam Knife and glue in place with Foam Tack Glue™ or the Low Temp Foam Glue Gun and Glue Sticks. Each Board measures 24" l x 8" h

This package includes 4 Risers, generally used with Incline Starters to create varying grades on your layout. Risers are easily flexed to form curves and work on plywood or foam bases. To install, pin in place with Foam Nails and attach with Foam Tack Glue™ or Low Temp Foam Glue Gun and Glue Sticks.Each Riser measures 2 in x 2 1/2 in x 24 in (5.08 cm x 6.35 cm x 60.9 cm)

This package includes 4 Incline Starters. Each piece elevates from 0 - 1 in (0 - 2.54 cm)within 24 inches. Incline Starters allow smooth transition from one height to another. To install, pin in place with Foam Nails and attach with Foam Tack Glue™ or the Low Temp Foam Glue Gun and Glue Sticks. Each piece measures 2 1/2 in x 24 in (6.35 cm x 60.9 cm)

This Incline Set includes 4 sections that rises 4 inches (10.1 cm) in an 8-foot (2.43 m) run. Incline Sets allow smooth transition from one height to another. To install, pin in place with Foam Nails and attach with Foam Tack Glue™ or the Low Temp Foam Glue Gun and Glue Sticks. Each piece measures 2 1/2 in x 24 in (6.35 cm x 60.9 cm)

This package includes 4 Risers, generally used with Incline Starters to create varying grades on your layout. Risers are easily flexed to form curves and work on plywood or foam bases. To install, pin in place with Foam Nails and attach with Foam Tack Glue™ or Low Temp Foam Glue Gun and Glue Sticks.Each Riser measures 1/2 in x 2 1/2 in x 24 in (1.27 cm x 6.35 cm x 60.9 cm)

This package includes 4 Risers, generally used with Incline Starters to create varying grades on your layout. Risers are easily flexed to form curves and work on plywood or foam bases. To install, pin in place with Foam Nails and attach with Foam Tack Glue™ or Low Temp Foam Glue Gun and Glue Sticks.Each Riser measures 1 in x 2 1/2 in x 24 in (2.54 cm x 6.35 cm x 60.9 cm)

This package includes 2 Risers, generally used with Incline Starters to create varying grades of dramatic, steep relief on your layout, and to create lower areas for rivers and valleys. Risers are easily flexed to form curves and can work with both plywood or foam bases. To install, pin in place with Foam Nails and attach with Foam Tack Glue™ or Low Temp Foam Glue Gun and Glue Sticks.Each Riser measures 4 in x 2 1/2 in x 24 in (10.1 cm x 6.35 cm x 60.9 cm)

This Incline Set inlcudes eight sections that rise 4 inches (10.1 cm) in a 16-foot (4.87 m) run. Incline Sets allow smooth transition from one height to another. To install, pin in place with Foam Nails and attach with Foam Tack Glue™ or the Low Temp Foam Glue Gun and Glue Sticks.Each piece measures 2 1/2 in x 24 in (6.35 cm x 60.9 cm)

This package includes 8 Incline Starters. Each piece elevates from 0 - 1/2 in (0 - 1.27 cm) within 24 inches. Incline Starters allow smooth transition from one height to another. To install, pin in place with Foam Nails and attach with Foam Tack Glue™ or the Low Temp Foam Glue Gun and Glue Sticks.Each piece measures 2 1/2 in x 24 in (6.35 cm x 60.9 cm)

Bend ¼-inch Foam Sheets into a radius to create tunnels with curves or use for other craft projects. Pin with Foam Nails and glue in place with Foam Tack Glue™ or the Low Temp Foam Glue Gun and Glue Sticks. Foam Sheet measures 12" w x 24" (6 mm) 1 sheet/pkg

Use ½-inch Foam Sheets for layout and diorama bases, as well as to form tunnel walls, ceilings or overpass supports. Pin with Foam Nails and glue in place with Foam Tack Glue™ or the Low Temp Foam Glue Gun and Glue Sticks. Foam Sheet measures 12" w x 24" 1 sheet/pkg

Use 1-inch Foam Sheets for layout and dioramas bases, to build elevated areas and supports, or for other craft projects. Pin with Foam Nails and glue in place with Foam Tack Glue™ or the Low Temp Foam Glue Gun and Glue Sticks. Foam Sheet measures 12" w x 24" l. 1 sheet/pkg

Use 2-inch Foam Sheets for layout and diorama bases, to build elevated areas, mountains and terrain contours and for supports or other craft projects. Pin with Foam Nails and glue in place with Foam Tack Glue™ or the Low Temp Foam Glue Gun and Glue Sticks.Foam Sheet measures 12" wide x 24" long. 1 sheet/pkg

Use 3-inch Foam Sheets for layout and diorama bases, to create flat areas for towns, to build bridges and other structures or for other craft projects. Pin with Foam Nails and glue in place with Foam Tack Glue™ or the Low Temp Foam Glue Gun and Glue Sticks.Foam Sheet measures 12" wide x 24" long.

Use 4-inch Foam Sheets for layout and diorama bases, to create flat areas for towns, to build bridges and other structures and for other craft projects. Pin with Foam Nails and glue in place with Foam Tack Glue™ or the Low Temp Foam Glue Gun and Glue Sticks. Foam Sheet measures 12" wide x 24" long. 1 sheet/pkg

Foam Pencils have a special lead designed to draw on foam without causing damage. The colors will not bleed through paint or other coverings. Each package contains two red and two black pencils.

Use Foam Nails to temporarily pin track, foam or other products to your layout. 75/pkg - 2 in (5.08 cm) ea.

2-inch long replacement blades for the Woodland Scenics Foam Knife. 4/pkg

Special nichrome wire retains an even temperature needed to cut SubTerrain® foam products. Use only with the Hot Wire Foam Cutter. length - 48 in (121 cm)3gauge. - 30 or 0.010 diameter.

Specially formulated for foam and also effective on wood, cork and Homasote board. Foam Tack Glue is high-tack, non-toxic and water soluble. It dries clear and flexible. Use as a contact cement whenever bonding two large surfaces. 12 fl oz/354mL

Foam Putty to fill cracks, sculpt and carve with foam.

Use with Low Temp Foam Glue Gun. Bonds to foam, wood, paper, foil and many other craft materials. 10" x 3/4" (25.4cm x 1.9cm) - 10/pkg

Use Casting Plaster to make rocks, fossils, animal tracks, lava flows or other forms for any plaster casting project. 8 oz package Ages 7 and up. Adult supervision recommended for younger children.

Plaster Cloth is versatile, fun and easy to use! Apply wet Plaster Cloth to newspaper wads, balloons and other forms to make lightweight, hard shell land terrain, masks and other shapes. Plaster Cloth forms virtually to any shape, is easy to paint, dries quickly and is non-toxic. Roll measures 8" x 3.75 yd, 7.5 sq ft. (20.3cm x 3.42m, 69.6 dm2)

The most popular and comprehensive scenery manual available. Anyone can make beautiful, realistic scenery, and this manual will show you how. The spiral-bound Scenery Manual is loaded with various tips, techniques, ideas and instructions for using more than 600 Woodland Scenics products. 142 pages contains hundreds of full-color photos and illustrations. ©1994, 2001 and 2007

Smooth-It is a plaster material that is used to smooth rough spots, create streets, roads and parking lots. Mix with water and apply directly to any clean hard surface. Covers 26' by 3" by 1/4" (HO Scale - two-lane highway).

Road System - Create paved areas, such as highways, roads, streets, curbs, footpaths, and railway crossings.

Top Coat Concrete is a non-toxic, water-soluble compound used to simulate the color of concrete road surfaces. Brush-on application. 4 fl oz (118 mL). One bottle will cover approximately 9 to 12 square feet.

Road System - Create asphalt areas, such as highways, roads, streets, footpaths, and railway crossings.

Strips are the perfect roadbed for tight track applications. They align well with cork or Homasote and install easily with Foam Tack Glue (ST1444). Pin in place with Foam Nails (ST1432). Bulk Pack saves over purchasing items separately. 36 Strips/pkg. 3/16" x 1 ¾" x 24" each (5mm x 44.4 cm x 60.9 cm)

Strips make the perfect roadbed for tight track applications, and offer a smooth, almost seamless application. It deadens sound, requires no pre-soaking like cork, remains flexible and will not dry out or become brittle! Aligns well with cork or Homasote applications. 12 Strips per package. Install Track-Bed with Foam Tack Glue (ST1444). Pin in place with Foam Nails (ST1432). 3/16 in x 1 3/4 in x 24 in 5 mm x 4.44 cm x 60.9 cm

There are 12 Strips in this Track-Bed Standard Pack. These strips are the perfect roadbed for especially tight track applications. The Strips are 3mm x 1 1/4" x 24". Track-Bed requires no pre-soaking like cork does: it remains flexible and won’t dry out or become brittle! It aligns well with cork or Homasote applications. Install Track-Bed with Foam Tack Glue (ST1444). Pin in place with Foam Nails (ST1432). Also works great for H0n3 and Hon30 gauge!Track underlay - grey foam. Part of Subterrain system.

Track-Bed Roll offers a smooth, almost seamless application. It deadens sound, requires no pre-soaking like cork, remains flexible and will not dry out or become brittle! Aligns well with cork or Homasote applications. Install Track-Bed with Foam Tack Glue™ (ST1444). Pin in place with Foam Nails (ST1432). 13/64 in x 1 3/4 in x 24 ft 5 mm x 7 cm x 7.31 m