CP6

Provides circuit protection for up to 6 sections of your railway. Operates with ANY DCC system. Factory set to 1 Amp per section. Sections can be connected together for more power per section. See optional lamp packs below for 1.75 Amps per section

CP6-17 - Lamp 21 watt

Pack of 6 replacement lamps for the CP6 circuit protector. 1.7 Amp

Antenna Base Station HG

1/2 Wave Antenna, 900 MHz. Used with RB-02 base station and RPT-1 repeater

Antenna Throttle

1/4 Wave Antenna, 900 MHz. Can replace the HG antenna when upgrading older radios throttles to Generation III

UTP CAT Panel

The operator side is fitted with RJ-12 jacks for throttles while offering CAT5 cable connections for improved noise rejection on larger layouts using standard computer CAT 5 cables. This board also provides a convenient point to add additional 12 Volt cab bus power when bus lengths exceed 20 meter [60 feet]. Shown with the included 1/16" thick aluminum, black anodized fascia plate.

NCE DIN Coil Cable

7 foot coiled cord with molded right angle DIN plug.

NCE DIN Panel

This panel combines low cost with rugged DIN jacks for long life. RJ-12 jacks provided on back for easy plug and play installation. Solder holes also provided for high reliability hard wired installation. Includes a 1/16" thick aluminum, black anodized fascia plate.

NCE Cable RJ12-7

7 foot RJ12 cable for connecting UTP/DIN panel

LEDs

The LED pack provides ten "Sunny White" LEDs. Size: 0.120" (3 mm) diameter. Rated at 3 to 20 mA.

DTK

Decoder Test Kit. Perfect companion to DCC installation and operation, the decoder tester works with ANY DCC decoder and tests for motor forward and reverse, functions 0F, 0R, 1, and 2. Fitted with test plug's for NMRA 8 pin and JST 9 pin plugs. Supplied with 9 pin to 9 pin cable and a 9 pin and cable which the user can add parrot beak cables to allow testing decoders like the DA-SR and any wire in decoders. Screw terminal to add motor for testing BEMF decoders.

NCE Cable RJ12-40

40 foot RJ12 cable for connecting UTP/DIN panel

USB Computer Interface

Add this USB computer interface for computer programming and/or operation of your Power Cab equipped layout. Requires USB cable, computer and railroad computer program such as JMRI Decoder Pro and Panel Pro.

Download the USB Driver that you need for your type of computer: Click Here then click on Microcontrollers, then Software Downloads, then cp210x VCP Drivers, then click on the VCP Driver Kit for your computer

Download JMRI Decoder Pro/Panel Pro to both program and operate your railway.

Auto Switch

Prevents accidental programming of ALL locos on your track when using Program Track mode. Automatically disconnects your main line when in Program Track mode (does not affect Program on Main). Compatible with ALL DCC systems such as DigitraxTM Big Boy, Empire Builder and Bachmann EZ-CommandTM

Plug Pack

Ten pack of the NMRA eight-pin connectors used in many "DCC Ready" locomotives and accessories.

Lamp 18 watt

Pack of 6 replacement lamps for the CP6 circuit protector. 1.00 Amp

Mini Panel

Use one button to control multiple switches or macros on your NCE DCC system. You can have up to 30 pushbuttons, toggle switches, block detectors,etc. Can be connected for control of turnouts, signals and other devices. Easy programming, just plug in a Pro Cab. Simple hook up, one Cab Bus connection and 2 wires for each pushbutton or other input device. Can be used to perform simple automatic train control and other layout automation tasks.

Dual Relay Board

Connects to a Switch-it or Switch 8 decoder to provide two SPST or one DPDT relay output for switch up to 2 amps of power.

Typicial uses:

• Control polarity of dead frogs
• Automatic reverse loop control
• Turn staging yard tracks on on/off
• Provide isolated turnout position information to signaling
• Computer control using AIU-01

Packet Analyzer

The NCE Packet Analyzer and your computer will view DCC packets being sent by any DCC system. Selectively filter out idle, reset, accessory, function and/or speed packets. Information can be displayed in hexidecimal or our special "verbose" mode that makes it easy to decipher track activity. Requires PC, Mac or Linux computer with terminal program and 9 pin serial cable. Can also be used to monitor NCE Cab Bus activity.

Switch-It Decoder

Control two Tortoise or similar stall motor switch machines. Switch-It remembers the position of your switches during power outages. Each output of the decoder can have a completely different accessory address. The Switch-It provides connections for "local control" pushbuttons. Control switches from your cabs and your control panels.

Snap-It Decoder

Control one twin coil switch machine. Has capacitive discharge for low current draw of track power. Provides connections for two "local control" pushbuttons. You can control switches from your cabs and your control panels.